GUIDE
Most sizing errors start with an annual average and end with a chiller holding half a day's kill. Here is the arithmetic to do first, and four points that decide whether a China-built unit fits.

Take the busiest seven days in the first two years, not the yearly figure divided by 52. Lamb season and festival demand push the peak to two or three times the average. Three numbers follow: head per kill day, average hot carcass weight, and the hours the crew can work before the chiller is full.
A unit described as 20 cattle per day describes the line, not the storage. If the chiller holds twelve carcasses, the twentieth animal waits until the first twelve are cold enough to move. Ask for throughput and buffer separately.
Volume is the number buyers compare, but rail length limits the load: the gap between rails is volume you cannot hang anything in.
| Planning figure, per head | Cattle | Sheep and lamb |
|---|---|---|
| Hot carcass weight | 280-320 kg | 20-25 kg |
| Rail length | 0.9 m | 0.4 m |
| Chilled volume | 1.0 m³ | 0.35 m³ |
| Water use | 600-1,200 L | 60-120 L |
| Wastewater to hold | 500-900 L | 50-90 L |
Allow about 70% of geometric volume as usable chilled space, since evaporator, fans and air circulation take the rest. Then check the rail: a 40 ft body gives roughly 12 m per tier, so two tiers carry about 26 cattle at 0.9 m each, or 60 lambs at 0.4 m.
| Body length | Rail per tier | Two tiers, cattle | Two tiers, sheep |
|---|---|---|---|
| 20 ft (6.0 m) | 6.0 m | about 13 head | 30 head |
| 40 ft (12.0 m) | 12.0 m | about 26 head | 60 head |
At 40 cattle a day no single trailer solves it: two units, a second shift, or a fixed chiller at the farm. Better to hear that before the deposit.
Water is often underestimated: cattle draw 600-1,200 L per head and sheep 60-120 L, so 20 cattle a day means 12-24 m³. An onboard tank of 500-1,500 L is a buffer, not a day's supply; the site needs a hydrant, a storage tank or a scheduled bowser. Wastewater is 70-80% of what goes in, so plan holding or tanker collection on the same scale.
Refrigeration follows physics. Dropping meat from 35 °C to 4 °C takes roughly 100-150 kJ per kg once surface moisture and door openings are counted. Twenty cattle at 300 kg is 6,000 kg, or 600,000-900,000 kJ; over a 12-hour pull-down that averages 14-21 kW, so size at the top of the range. A 25-30 kVA generator covers that load, including fan and pump starting current. Shore power is cheaper per hour where the supply is adequate, and 50 or 60 Hz must be fixed before the order: a motor wound for one frequency runs at the wrong speed on the other.
Cattle drive the structure: hoist rated for carcass plus pulling force, a stunning pen for 600 kg of live animal, a splitting saw, and rail height that clears the floor. Sheep drive the rhythm: no splitting, shorter rail spacing, a bleeding trough and more head per metre, which is why the same body carries 60 lambs or 26 cattle. Mixed-species buyers should price the changeover: rail spacing, restraint and crew position all change.
A 6-8 m body plus drawbar needs a turning circle and a gate width many farmyards lack. Check the route in the wet season, not in August: soft ground, slope at the unloading point, overhead cables, and where the generator will stand. A unit that cannot reach the paddock in March is a fixed plant with wheels.
A China supplier can meet the mechanical specification and still leave you with a machine you cannot license or service. Settle four points in the enquiry.
Any manufacturer can quote a number; fewer can quote the right one. Send the species split, peak head per day, carcass weight, kill hours, water and waste arrangements, available power, access dimensions, destination country and port, and the status of your approval application. Those nine items let a supplier size rail, chiller, tanks and electrical package.
HUAYI EQUIPMENT builds mobile slaughter units in trailer and container formats in China and exports them with a loading plan, electrical specification and spares list for the destination. Send the nine items above and we will return a configuration with rail length and tank volumes shown, so you can check the arithmetic.